A polyurea coating is an elastomeric membrane formed by the fast reaction of two components, an isocyanate and an amine resin, hot sprayed onto steel or concrete. In a single operation it gives a thick, continuous, flexible and watertight film that can return to service very early. Its results depend mostly on substrate preparation, moisture and the setup of the spray equipment.
It goes by several names: spray polyurea, polyurea membrane, spray elastomer. This guide is written for maintenance, environmental and project managers at industrial sites in Quebec and Ontario who need to decide whether polyurea suits their asset. Detailed comparisons with epoxy already exist on our blog and are linked below rather than repeated. Induscoat works on industrial and commercial assets only, not on residential jobs such as garages or basements.
What is a polyurea coating?
It is an elastomer produced by the reaction of an isocyanate component with a blend of amine-terminated resins. The reaction starts on mixing, with no solvent, and the membrane sets very quickly: a substantial thickness can be built up in successive cross passes, with no sagging on vertical walls.
What sets polyurea apart from conventional paints:
- Thickness. It is a membrane rather than a paint film; the target thickness comes from the data sheet and the specification.
- Flexibility. It stretches without tearing, follows substrate movement and can bridge fine cracks.
- Continuity. Sprayed without seams, it forms a watertight envelope around corners, penetrations and irregular shapes.
- Speed. Return to service, set by the data sheet, comes much earlier than with an epoxy.
It is applied on steel, concrete and other substrates, always over a suitable primer. It is part of our protective coatings work, alongside epoxies and anticorrosion systems.
Pure or hybrid polyurea: what is the difference?
The difference lies in the resin blend: a pure polyurea contains amine resins only, while a hybrid mixes amines and polyols, which also forms urethane linkages. Both are sprayed with the same type of equipment, but they do not behave the same way.
| Criterion | Pure polyurea | Polyurea-polyurethane hybrid |
|---|---|---|
| Resin blend | Amine resins only | Mix of amines and polyols |
| Reaction speed | Very fast | Slower, varies with the formula |
| Moisture sensitivity during application | Low | Higher, risk of bubbling |
| Sensitivity to application temperature | Low | Higher |
| Mechanical and chemical properties | High, detailed on the data sheet | Highly variable from one product to another |
| Typical uses | Containment, basins, wear, immersion per the data sheet | General protection, less demanding service |
A hybrid is not a bad product, but the word "polyurea" on the label is not enough to judge: read the data sheet, the declared composition and the chemical resistance chart. Another distinction matters outdoors: aromatic polyureas, the most common, yellow in sunlight, while aliphatic grades keep their colour and are often used as a topcoat.
How is hot spray polyurea applied?
It is applied with a plural-component proportioner that heats and pressurizes both products, heated hoses and a gun that mixes them by impingement at the tip. Mixing therefore happens in the gun, at the last moment, which explains how fast the reaction is.
The job follows a set order:
- Substrate preparation. Abrasive blasting of steel or mechanical preparation of concrete, repairs, treatment of cracks and joints.
- Primer. It seals concrete porosity, limits the outgassing that creates craters and pinholes, and secures adhesion on steel.
- Equipment setup. Temperatures, pressures and mix ratio are set to the data sheet and checked with a test spray before touching the asset.
- Spraying. Cross passes up to the specified thickness, respecting the recoat window over the primer and between passes.
- Inspection. Thickness, appearance, continuity and adhesion, recorded in the job log.
The usual checks are thickness measurement (SSPC-PA 2 on steel, ASTM D6132 or witness samples on concrete), pull-off adhesion testing (ASTM D4541 on steel, ASTM D7234 on concrete), a holiday test for continuity (ASTM D4787 on concrete) and, where the specification requires it, durometer hardness to ASTM D2240.
The crew has to master this equipment: a deviation in temperature or mix ratio gives a soft, tacky or brittle membrane. Isocyanates call for suitable respiratory protection, ventilation and a safety perimeter, and overspray travels far: everything that must not be coated is masked. There are also slow-cure polyureas applied by roller, such as polyaspartics, used mostly as topcoats or on floors.
Where is polyurea used in industry?
It is used where a watertight, flexible membrane with a fast return to service is needed, on assets that move, take impacts or cannot stay out of service for long.
- Containment and secondary containment. Tank dikes and containment basins, where the membrane bridges active cracks in the concrete. Resistance to the stored product decides, as our article on concrete secondary containment coating explains.
- Basins and concrete structures. Process water basins, pits, trenches and channels, where watertightness and resistance to freeze-thaw cycles matter.
- Truck bodies, hoppers and decks. The membrane absorbs impact and reduces sticking of wet materials; our guide on polyurea for industrial equipment and truck bodies covers these cases.
- Process roofs. Process roofs and industrial roofs crowded with equipment, where a continuous membrane wraps around supports and penetrations. Outdoors, an aliphatic topcoat protects it from UV. For sheet metal roofs, see also our article on industrial metal roof coating.
- Exposed concrete. Dock slabs, ramps, wash bays and pit walls, where the concrete is cracked or takes impacts.
- Steel. Tank exteriors, piping and buried or damp structures, depending on the data sheet and the service.
On concrete, preparation targets the CSP profile set by the data sheet according to ICRI 310.2R, as described in our article on concrete surface preparation by shot blasting or grinding.
What are the limits of polyurea?
Its main limits are the UV resistance of aromatic grades, the preparation it demands, its sensitivity to substrate moisture and a chemical resistance that varies widely from one product to another. They can be managed if they are known before choosing.
- UV. An aromatic polyurea yellows and chalks on the surface in sunlight. Protection often remains good, but appearance degrades; an aliphatic topcoat solves this.
- Preparation. The membrane only adheres to a clean, sound and profiled substrate. Polyurea sprayed over laitance, grease or rust peels off in sheets, often far from where the failure started.
- Substrate moisture. Damp concrete outgasses under the membrane and causes bubbles and pinholes; moisture is measured before the job, as our article on concrete moisture before coating explains. The surface must also stay above the dew point.
- Chemicals and heat. Strong acids, some solvents and oxidizing products can swell or soften the membrane, and its properties drop above the service temperature on the data sheet.
- Short recoat window. Once the window has passed, a new coat only adheres after abrasion and a re-coat primer; this matters for repairs.
- Mobilization. Heated spray equipment and a specialized crew weigh heavily on small areas, where another system can be simpler.
Polyurea or epoxy: how do you decide quickly?
Polyurea wins when the substrate moves, when return to service must be fast or when the job is done in the cold; epoxy often wins against aggressive chemicals and when a hard film that is simple to apply and touch up is wanted. Both demand the same rigour in preparation.
Rather than repeat our comparisons, here is where to find the detailed decision:
- For a containment basin or tank dike: polyurea vs epoxy for secondary containment.
- For a plant floor: epoxy vs polyurethane vs polyurea flooring.
In mixed cases, a combined system is common: an epoxy primer under the polyurea, or polyurea overcoated with a more chemically resistant topcoat.
How do you get a polyurea coating done at an industrial site?
Start by describing the asset, the substrate, the products in contact and the shutdown window, then set the preparation, system, thickness and inspections before discussing the schedule. Our polyurea coatings service covers substrate preparation, spraying, continuity testing and the inspection records.
Our crews and qualified subcontractors work out of LaSalle, in Montreal, Bécancour and across Quebec and Ontario. Send photos, dimensions, the type of substrate and the list of products in contact through the request a quote form: pricing on consultation, reply within 24 business hours.
Frequently asked questions
What is the difference between polyurea and polyurethane?
Both are isocyanate-based elastomers, but polyurea reacts with amines and polyurethane with polyols. Polyurea reacts much faster and tolerates moisture and cold better during application; polyurethane, being slower, can often be applied with simpler equipment.
Can polyurea be applied on damp concrete?
Not without precautions. The concrete must meet the moisture limit on the data sheet for the primer and the membrane, measured before the job. Some primers tolerate damper concrete, but moisture remains the leading cause of bubbles and disbondment.
Does polyurea stand up to sunlight?
An aromatic membrane keeps its mechanical properties, but it yellows and chalks on the surface. For a roof, an outdoor dike or exposed equipment, an aliphatic topcoat that is UV stable is planned.
Can a damaged polyurea membrane be repaired?
Yes. The area is cut out or abraded back to sound membrane, cleaned and treated with the re-coat primer called for on the data sheet, then resprayed or repaired with a compatible product that overlaps the existing membrane.
Hicham M, P Eng, PMP
Engineer and project manager (PMP) at Induscoat. Over 16 years of experience in industrial coatings, composite repairs and wear protection on mining, energy and petrochemical sites in Canada and internationally.
